Power Sequence
- VBUS attach: the CD3217s wake from their own LDOs and negotiate 5 V first, then 20 V once their firmware runs. PPBUS_AON should read around 12.3 V.
- PP3V8_AON: a buck from PPBUS_AON, then through the current-sense path into both PMUs.
At startup only the first phase is active.
Given the coils on phase 2&3 (`L5840`, `L5820`) are bigger than on phase 1 ('`L5800`), we can assume Phase 1 is the only active phase at startup or when in standby, and either P2/P3 take over when the device is on, or supplement P1.
The buck controller is an Renesas `RAA225501C` (Apple P/N `353S02645`) - its data sheet is not available (. - AON LDOs from MPMU and SPMU: 1V8_AON, 1V2_AON and 1V5_LDOINT per PMU, plus PP3V3_AON and a 5 V boost (BSTLQ). Charger current is ~30–40 mA at this stage.
- Wake event (button, lid, charger): the S2 rails come up, e.g. PP5V_S2, PP3V3_S2, PP1V8_S2, PP1V25_S2, PP0V88_S1, PP0V72_S2_VDD_LOW, PP1V2_AWAKE_PLL, PP0V855_S2SW_CIO, followed by the AWAKE/NAND rails.
- SoC starts, SPMI handshake with the PMUs, then S0 rails. This is the part I'm least sure of in detail.
The following information is for an A2338 MacBook Pro M2 (13 inch), and must be verified with some 14" or 16" Pro/Max variant.
-
USB-C connection is detected
The USB-C connector
JE700presents theUSBC0_CC1_CONNsignal throughUF300. -
Initial 5 V USB-C input appears
The charger supplies approximately 5 V on
PPVBUS_USBC0. This is the default USB-C voltage before Power Delivery negotiation. -
USB-C controller auxiliary supply starts
USB-C controller
UF400(CD3217B) generatesPP3V3_UPC0_LDO.This rail powers the controller's external SPI ROM
UF260(25Q80), accessed through:SPI_UPC01_R_CS_LSPI_UPC01_R_CLKSPI_UPC01_R_MOSISPI_UPC01_R_MISO
-
The initial 5 V reaches the charger input
The input passes through
PPHV_INT0_AONSW, fuseFF200and current-sense resistorR5220, becomingPPDCIN_USBC_AON.At this point, the input is still approximately 5 V because USB Power Delivery negotiation has not yet raised VBUS.
-
The charger controller becomes operational
Charger controller
U5200(ISL9240HI) receives its required bias and sensing connections throughVDDP,VDDA,CELLandPBUS. -
The charger initially operates in boost mode
U5200, together with MOSFETsQ5230andQ5240and inductorL5230, operates as a boost converter.This raises the initial USB-C input sufficiently to establish the system bus.
-
The 13 V system bus is established
PPBUS_AONrises to approximately 13 V while the charger is operating in boost mode.This rail supplies the always-on power system, including
U5700. -
The main voltage-regulator enable is generated
U5200activatesCHGR_EN_MVR. Through logic deviceU5340, this producesP3V8AON_PWR_EN. -
The 3.8 V always-on rail starts
P3V8AON_PWR_ENenablesU5700(RAA225501C).U5700then generates: -
The PMU always-on and standby LDO rails start
PP3V8_AON supplies the main PMU U8100 and secondary PMU U7700. The diagram marks the following rails as part of this stage.
From U8100:
PP1V8_AON_MPMUPP1V8_AONPP3V3_S2_LDOPP1V2_AWAKE_PLLPP1V2_AON_MPMUPP3V3_AONPP0V855_S2SW_CIOPP3V3_S2SW_SNSPP1V2_S2_CIOPP1V5_LDOINT_MPMU
From U7700:
PP1V2_AON_SPMUPP0V72_S2_VDD_LOWPP0V8_S1_VDD_FIXED
- The main PMU crystal oscillator starts
Crystal Y84A1 starts oscillating and supplies MPMU_XOUT to U8100.
- The 32.768 kHz SoC clock becomes available
U8100 provides PMU_CLK32K_SOC from its SLEEP_32K output to the M2 SoC U0600.
- A power-on request is received
The active-low PMU_ONOFF_L signal is asserted, normally by pressing the power button.
The diagram also shows IPD_LID_OPEN_1V8 as an input to the main PMU, although it is not assigned a separate sequence number.
- The PMUs enable the main SoC and SSD rails
U8100 and U7700 enable the switched AWAKE, S1 and S2 rails required by the M2 SoC and onboard NAND storage.
PPVDD_AWAKE_PCPUPPVDD_AWAKE_GPUPPVDD_S1_SOCPP1V8_S2PPVDD_S2SW_VDD2HPPVDD_AWAKE_CPU_SRAMPPVDD_S1_DCSPPVDD_AWAKE_ECPUPP1V25_S2PP1V8_AWAKEPP1V25_AWAKE_IOPP0V779_S1_SRAMPPVDD_S1_DISPPPVDD_S1_VDDQLPP0V88_S1PP1V12_S2SW_AMPH
PP2V58_AWAKE_NAND_VCCPP1V25_AWAKE_NAND_VCCQPP0V88_AWAKE_NAND_VDD
The diagram assigns all these rails to stage 14. It does not establish their exact internal order.
- The M2 24 MHz reference clock starts
Crystal Y0714 provides the 24 MHz reference clock for the M2 SoC.
- SoC reset is released
The main PMU releases PMU_RESET_L, connected to the SoC's COLD_RESET* input.
Because the signal is active-low, “released” normally means that it transitions high.
- The SoC boot ROM is accessed
The M2 SoC communicates with SOCROM U1900 (25S64) over SPI:
SPI_SOCROM_CS_LSPI_SOCROM_CLK_RSPI_SOCROM_MOSI_RSPI_SOCROM_MISO
- Firmware initialization and hardware self-test begin
- Complete internal SoC initialization.
- Verify RAM.
- Verify devices on the SPMI and I²C buses.
- Verify NAND storage and read its low-level data.
- Verify the configuration/logic EEPROM.
- Verify the trackpad and fingerprint sensor.
Communication shown during this stage includes:
SPMI_NUB_MPMU_CLKSPMI_NUB_MPMU_DATASPMI_NUB_SPMU_CLKSPMI_NUB_SPMU_DATAI2C_SEEPROM_SCLI2C_SEEPROM_SDA- NAND SPI and PCIe connections
- USB-C controller communication is established
The system communicates with UF400 through:
I2C_SMC_UPC_SDAI2C_SMC_UPC_SCLUPC_SMC_I2C_INT_L
- The USB-C CC1 connection is processed
The USBC0_CC1 signal reaches the C_CC1 input of UF400, allowing the USB-C controller to identify and communicate with the connected power adapter.
- USB Power Delivery raises VBUS to 20 V
After successful USB-PD negotiation:
PPVBUS_USBC0rises from approximately 5 V to 20 V.PPHV_INT0_AONSWalso rises to approximately 20 V.- The higher voltage reaches
PPDCIN_USBC_AON.
- The charger detects the negotiated adapter voltage
U5200 senses the elevated input through AUX_DET.
- The charger changes to buck mode
Once the negotiated input voltage is above the required system-bus voltage, U5200 changes from boost operation to buck operation.
- The 13 V bus is maintained in buck mode
U5200 steps the approximately 20 V USB-C input down to maintain:
PPBUS_AONat approximately 13 V
The same system-bus node can also receive power from the battery through Q5265 and PPVBAT_AON.