Skip to main content

Power Sequence

Power Sequence — MacBook Pro Apple Silicon (M-Series Pro / Max & Base)

Status: Active Reference / Verified against A2338 (M2 13") & A2779 (M2 Pro 14", 820-02841).

Scope: Covers power delivery architecture for Apple Silicon MacBooks (M1/M2/M3/M4 Pro & Max series).

Source Tags: [diagram] Schematic Power-Sequence Diagram · [measured] Bench Measurement · [inferred] Inferred / Logic Flow.

Power Stages at a Glance

Stage Steps Key Architecture & Rail State Typical USB-C Ammeter Behavior
Stage A 1–7 USB-C Attach, 5V VBUS, Charger Boost Mode, PPVDD_AON_MAIN / PPBUS_AON established 5.0 V / 0.00 A – 0.03 A
Stage B 8–9 Enable chain for PP3V8_AON Buck Regulator 5.0 V / 0.03 A – 0.05 A
Stage C 10–12 PMU Always-On rails, Main PMU Crystal (24MHz/32kHz clocks to SoC) 5.0 V / 0.05 A – 0.08 A
Stage D 13–14 Power-On Request, PMU AWAKE / S1 / NAND / S2 Rails enabled 5.0 V / 0.08 A – 0.15 A (or Stuck in DFU)
Stage E 15–18 SoC Reset Release, Secure Enclave Boot, Internal ROM & NOR Firmware execution 5.0 V ➔ 20.0 V Transition
Stage F 19–24 SMC/PMU ↔ CD3217 Handshake, Negotiate 20V/28V PD, Charger switches to Buck Mode 20.0 V / 0.50 A – 2.50 A+

Stage A — USB-C / MagSafe Attach & System Bus Generation

Steps & Signals

  1. Physical Connection Detected [diagram]
    USB-C (JE700) presents USBC0_CC1_CONN / USBC0_CC2_CONN or MagSafe 3 detects cable insertion.
  2. Initial 5V VBUS Input Appears [diagram]
    Charger inputs 5V on PPVBUS_USBC0.
  3. USB-C Controller Auxiliary LDO Starts [diagram]
    CD3217 / ACE Port Controller (UF400) generates local LDO PP3V3_UPC0_LDO. Powers local SPI ROM (UF260) for CD3217 configuration loading (SPI_UPC01_R_CS_L, CLK, MOSI, MISO).
  4. VBUS Passes Ingress Filter to Charger [diagram]
    Passes input MOSFETs (PPHV_INT0_AONSW), Fuse (FF200), and sense resistor (R5220) to form PPDCIN_USBC_AON.
  5. Intersil / Renesas Charger IC Power Up [diagram]
    Charger IC (U5200, e.g., ISL9240 / ISL9241 or Apple Custom PMU Charger) powered via VDDP / VDDA.
  6. Charger Enters Boost Mode [diagram]
    Since VBUS is only 5V and battery may be depleted/disconnected, the Charger IC operates in Boost Mode to raise system voltage to ~12.0V–13.1V.
  7. System Main Rail Established (PPVDD_AON_MAIN / PPBUS_AON) [diagram]
    PPVDD_AON_MAIN is generated. This is the primary system power bus feeding all secondary buck regulators.

🔴 Stage A Failures & Troubleshooting

Symptom: 0.00 V / 0.00 A or stuck at 5.0 V / 0.00 A.

Common Faults:

  • Blown Input Fuse (FF200) or shorted input MOSFETs.
  • Short circuit on PPVDD_AON_MAIN (very common — cracked ceramic capacitor or dead ISL9240).
  • Missing PP3V3_UPC0_LDO due to a dead CD3217 IC or corrupt/missing SPI ROM (UF260).

Stage B — 3.8V Always-On Rail (PP3V8_AON)

Steps & Signals

  1. Enable Signal Issued [diagram]
    PPVDD_AON_MAIN reaches stable voltage threshold, triggering VDD_MAIN_PWR_GOOD or internal PMU enable lines.
  2. PP3V8_AON Buck Regulator Starts [diagram]
    Multi-phase PMIC / Buck Regulator generates PP3V8_AON (~3.8V).
    Note: PP3V8_AON is critical as it directly powers the primary System PMUs (PMU_TOP / PMU_MAIN).

🔴 Stage B Failures & Troubleshooting

Symptom: Stuck at 5.0 V / 0.01 A – 0.03 A.

Common Faults:

  • Short circuit on PP3V8_AON (Feeds multiple audio, wireless, and PMU circuits).
  • Blown inductor or damaged PMIC drive circuit on the 3.8V switching phases.

Stage C — PMU Always-On Rails & System Clocks

Steps & Signals

  1. Main PMUs Boot Up [diagram]
    Primary PMU receiving PP3V8_AON outputs core AON rails:
    • PP1V8_AON (GPIO & PMU Logic)
    • PP1V2_AON / PP0V8_AON (SoC Secure Enclave RTC & Standby Cores)
    • PP3V3_AON (Sensors & Boot ROMs)
  2. Main Crystal Oscillator Starts [diagram]
    PMU activates 24 MHz RTC / 32.768 kHz clock output.
  3. Always-On Clocks Routed to SoC [diagram]
    Low-power clocks routed to SoC Always-On domain to enable power-state monitoring.

🔴 Stage C Failures & Troubleshooting

Symptom: Stuck at 5.0 V / 0.03 A – 0.05 A.

Common Faults:

  • Short circuit on PP1V8_AON or PP0V8_AON (Often indicates dead SoC Always-On block or shorted decoupling cap).
  • Dead 24MHz/32kHz Crystal.

Stage D — Power-On Request & SSD / AWAKE Rails

Steps & Signals

  1. Power-On Trigger / AWAKE State [diagram]
    PMU detects lid open, keypress, or charger insertion and asserts PMU_SYS_ALIVE / AON_PWR_GOOD.
  2. SSD & S1/S2 Secondary Rails Enabled [diagram]
    PMUs turn on NAND Flash power rails:
    • PP2V5_NAND_AON
    • PP1V2_NAND / PP0V9_NAND
    S2RAM & SOC Core Standby Rails startup (PP1V8_S2RAM, PPVDD_SOC_S1).

🔴 Stage D Failures & Troubleshooting

Symptom: Board stuck in DFU Mode or 5.0 V / 0.05 A - 0.10 A Boot Loop.

Common Faults:

  • Short circuit on PP2V5_NAND_AON or damaged NAND chip (Very common on M1/M2/M3 boards).
  • Corrupted Apple Silicon Firmware / BridgeOS ➔ Requires DFU restore via Apple Configurator.

Stage E — SoC Core Execution & Firmware Boot

Steps & Signals

  1. SoC Reset Release [diagram]
    SOC_RESET_L / PMU_RESET_L is pulled high.
  2. High-Power CPU / GPU Rails Switched On [diagram]
    Secondary PMUs and DrMOS stages bring up:
    • PPVDD_CPU_E (Efficiency Cores)
    • PPVDD_CPU_P (Performance Cores)
    • PPVDD_GPU (Graphics Engine)
  3. Internal Boot ROM Execution [diagram]
    SoC executes internal ROM code, reads NOR Flash SPI, verifies Secure Enclave signature, and initializes RAM.
  4. Handshake to USB-C PD Subsystem [diagram]
    SoC software driver communicates with CD3217 / ACE port controllers over I2C/SPMI.

🔴 Stage E Failures & Troubleshooting

Symptom: Current rises to ~0.15 A – 0.30 A at 5V and shuts off, or loops.

Common Faults:

  • Blown DrMOS / Power Stage for PPVDD_CPU_P or PPVDD_GPU.
  • RAM / LPDDR5 power rail fault (PP1V1_S2RAM).
  • Corrupted NOR Flash.

Stage F — USB-C PD Negotiate (20V Switch) & Buck Mode

Steps & Signals

  1. SoC / PMU Requests High Voltage [diagram]
    System firmware commands CD3217 / ACE controllers to negotiate 20V (or 28V via MagSafe 3).
  2. Power Delivery Negotiation [diagram]
    CD3217 exchanges BMC packets on CC line with the USB-C Charger.
  3. VBUS Rises to 20V [diagram]
    USB-C Charger switches output from 5V to 20V.
  4. Charger Controller Switches to Buck Mode [diagram]
    Since input voltage (20V) is now higher than PPVDD_AON_MAIN (~12.5V), Charger IC (U5200) seamlessly switches from Boost Mode to Buck Mode.
  5. Battery Charging Enabled [diagram]
    Charger enables SMBus/I2C battery charging path if battery is connected.
  6. Full System Initialization & Display Output [diagram]
    Display backlight rails (PPVOUT_S0_BKLT), Audio, PCIe, and Thunderbolt peripherals powered on. macOS boots.

🔴 Stage F Failures & Troubleshooting

Symptom: Board boots and works at 5V (slowly), but never switches to 20V, OR shuts off immediately upon 20V switch.

Common Faults:

  • Faulty CD3217 / ACE Controller or dirty CC line communication.
  • Short circuit on a secondary 20V high-side MOSFET in the Charger or Backlight circuit (causes immediate shutdown when 20V hits the board).

Quick Diagnostic Flowchart for Repairs

[ Plug in USB-C Meter ]
        │
        ├── 0.00V / 0.00A  ► Check Fuse FF200, CD3217 LDO (PP3V3_UPC0_LDO), VBUS MOSFETs
        │
        ├── 5.00V / 0.00A  ► Check PPVDD_AON_MAIN (Short circuit?) & ISL9240 Charger IC
        │
        ├── 5.00V / 0.03A  ► Check PP38_AON, PP1V8_AON, PP0V8_AON (PMU Always-On)
        │
        ├── 5.00V / 0.08A  ► Check NAND Rails (PP2V5_NAND_AON). Plug into host Mac ➔ Check DFU Mode!
        │
        └── 20.0V / Dynamic ► Sequence Successful! If no display, check PPVOUT_S0_BKLT or Display Driver.