Skip to main content

M4 Pro Liquid Damage — USB-C PD Controller Corrosion

M4 Pro Liquid Damage — USB-C PD Controller Corrosion

Status: repaired successfully · Channel: LapFix · Published: 2026-07-06 · Runtime: 18:42 Model: MacBook Pro 14" M4 Pro (A3112 / A3185 series) · Board: 820-03487 [stated] Source: YouTube Fault class: USB-C Power Delivery / input power switching

Summary

Liquid ingress produced blue-green copper-carbonate corrosion across the feedback and gate-drive passives around the dual USB-C controllers. All three Thunderbolt 5 ports negotiated only 5 V with essentially no current draw, and the MagSafe 3 LED stayed dark. Cleaning the corrosion and replacing eroded 0201 passives restored a full 20 V / 3 A contract.

Timeline

Time Evidence Observation
02:15 [measured] USB-C meter shows 5.18 V on all three ports; current fluctuates 0.00–0.02 A. MagSafe 3 LED unlit.
05:40 [measured] Microscope: thick blue-green corrosion bridging feedback resistors and pass-gate control lines around both USB-C controller ICs.
09:12 [stated] Technician: on M4 Pro boards the USB-C controllers share power gating with the MagSafe controller, so a shorted CC or gate-drive pin freezes the PD handshake across all ports.
12:45 [measured] Corroded 0201 pull-up/series resistors removed, pads micro-scraped, re-tinned with 63/37 leaded solder, passives replaced from a donor board.
15:20 [measured] Re-test: port steps from 5 V to 20.2 V / 3.10 A; MagSafe 3 LED amber.
17:30 [measured] Boots to macOS setup; charging and multi-port Thunderbolt verified.

Measurements

Time Measurement Value Context
02:15 Voltage / current 5.18 V / 0.00–0.02 A All three USB-C ports, before repair
06:30 Diode mode 0.015 V CC1 on the damaged port (abnormal leakage)
15:20 Voltage / current 20.2 V / 3.10 A Fast charging after repair
15:35 Diode mode 0.565 V CC1 after repair

Diagnostic reasoning

  • Observation — every input path negotiates 5 V; MagSafe indicator dark; current stalls at 0–20 mA.
  • Stated mechanism — M4-generation power negotiation depends on synchronised bus state machines between the discrete USB-C controllers and the system PMU.
  • Inference — ionic conduction across corrosion products bridges the CC pull-down and gate-enable lines, preventing the controllers from reaching Attached.SNK.
  • Resolution — cleaning the corrosion and replacing the eroded 0201 series resistors restored normal impedance (0.565 V diode drop) and enabled the full 20 V / 3 A contract.

Repair procedure

  1. Disassemble chassis; extract logic board.
  2. Inspect the USB-C controller perimeter under the microscope.
  3. Desolder corroded 0201 resistors/capacitors (micro-pencil iron + hot air ~360 °C).
  4. Clean oxidised pads with a fibreglass brush and flux.
  5. Fit replacement 5.1 kΩ CC pull-downs and gate-drive series passives.
  6. Clean flux, verify MagSafe amber indication and battery charging.

Claims audit

ID Claim Evidence Note
C1 A shorted CC network on one port locks PD at 5 V across all ports on M4 Pro. [inferred] Directly demonstrated on this unit, but the "shared state machine" wording is the technician's model — verify against the board's actual PD topology.
C2 Modern Macs show an internal RTC date of 1 April because it is Apple's founding date, not an epoch artefact. [unverified] Asserted in passing; not substantiated at firmware level. Do not repeat as fact.
  • [[cd3217-ldo]] — the M1-generation analogue: one PD controller taking down every port.
  • [[cd3217-revision]] — PD-bus faults that are not liquid-related.

Provenance: condensed from the video's audio transcript (Google AI Studio); timestamps, refdes and values are as stated in the video and are not independently verified.