M2 Air Battery Not Detected — Sheared SMBus Pull-Up
M2 Air Battery Not Detected — Sheared SMBus Pull-Up
Status: repaired successfully · Channel: Alexey Lavrov · Published: 2025-05-29 · Runtime: 12:45 Model: MacBook Air 13" M2 (A2681) · Board: 820-02536 Source: YouTube Fault class: Sheared SMBus pull-up resistor → battery detection failure + CPU throttling
Summary
After a screen replacement the machine powered on from AC but reported the battery
as Not Installed, and the CPU throttled hard (kernel_task ~100 %, clock clamped
near 800 MHz). The narrow PCB peninsula near the display/webcam connectors — the
so-called "giraffe neck" — had lost the 0201 pull-up on SMBUS_BATT_SDA (reported
in the video as R5220; see the refdes note below), which pulls that line to 3.3 V.
It was sheared clean off its pads. A replacement 10 kΩ 0201 restored battery
telemetry, fast charging and normal clock speed.
Timeline
| Time | Evidence | Observation |
|---|---|---|
| 01:20 | [measured] |
Powers on from AC; battery menu shows Not Installed; CPU throttled (kernel_task ~100 %, ~800 MHz). |
| 03:40 | [stated] |
Alexey: the PCB layout near the display and webcam connectors forms a narrow peninsula ("giraffe neck"); 0201 passives here are frequently sheared off with metal tweezers during cable disconnection. |
| 06:10 | [measured] |
Microscope: the 0201 pull-up on SMBUS_BATT_SDA (reported as R5220) sheared clean off its pads next to the camera flex bracket. |
| 08:35 | [stated] |
That pull-up holds SMBUS_BATT_SDA at 3.3 V; with it missing the battery bus floats low, halting BMS telemetry. |
| 10:50 | [measured] |
Replacement 10 kΩ 0201 soldered on; battery recognised instantly, fast charging at 20 V / 2.5 A, CPU clock normal. |
Measurements
| Time | Measurement | Value | Context |
|---|---|---|---|
| 01:20 | CPU clock | ~800 MHz | Throttled state |
| 06:10 | Resistance | OL | Pads across the missing pull-up |
| 10:50 | Resistance / voltage | 10.0 kΩ / 3.30 V | Pull-up fitted; bus pulled high |
| 11:30 | Voltage / current | 20.0 V / 2.52 A | Normal charging profile |
Diagnostic reasoning
- Observation — loss of battery recognition and severe CPU throttling immediately following screen service.
- Stated mechanism — the A2681 layout leaves the battery I2C pull-up exposed to shearing during screen replacements.
- Resolution — confirming the missing pull-up and fitting a 10 kΩ part restored battery communication and eliminated the throttling.
Refdes note
The video identifies the sheared part as R5220. On the Pro/Max reference boards
(820-02098 / 820-02100) R5220 is the charger current-sense resistor in the
PPDCIN_AON path into U5200, not a battery-bus pull-up — see
[[power-sequence]]. This case is a different board (820-02536, M2 Air), so the two
can both be real refdes, but the collision means the designator in this case should
be treated as unconfirmed until it is read off the 820-02536 boardview. The
electrical finding (a 0201 pull-up on SMBUS_BATT_SDA sheared by display service)
does not depend on the designator.
Repair procedure
- Inspect the display-connector perimeter under a stereomicroscope.
- Clean the ripped copper pads with flux and a micro-iron tip.
- Position and solder a 10 kΩ 0201 resistor with a micro-pencil iron.
- Seal with UV conformal coating for mechanical durability.
- Boot and verify battery status and CPU performance.
Claims audit
| ID | Claim | Evidence | Note |
|---|---|---|---|
| C1 | Loss of the battery SMBus pull-up forces the Apple Silicon PMU into a thermal safe mode, throttling the CPU to minimum. | [inferred] |
The correlation is demonstrated; the exact throttle trigger (bus fault → safe mode) is the technician's explanation. |
| C2 | The sheared part is R5220. |
[unverified] |
Refdes as stated in the video. It collides with the charger current-sense R5220 on 820-02098/02100; confirm on the 820-02536 boardview before quoting the designator. |
Related cases
- [[m1max-smbus-tvs]] and [[m1pro-scl-open]] — the same bus failing electrically rather than mechanically.
- [[m1-las-backlight]] — another "damage during display service" failure mode.
- [[power-sequence]] — board-scoped reference that carries the other
R5220(charger current sense).
Provenance: condensed from the video's audio transcript (Google AI Studio); timestamps and values are as stated in the video and are not independently verified. The R5220 designator is flagged unconfirmed — see the refdes note above.