DIAGNOSIS_DATA_START SECT_START CD3217 Diag NOTE_START Top-Left USB-C - [p:UF400] - [n:PP3V3_UPC0_LDO] = ~5V from charger CD3217 internal LDOs - [n:PP1V5_UPC0_LDO_CORE]=1.5V - [n:PP3V3_UPC0_LDO]=3.3V - [n:PPHV_INT0_AONSW]= ~5V to System. If missing, check [n:USBC0_CC1] and [n:USBC0_CC2] resistance to GND. If different, replace [p:UF900] NOTE_END SECT_END SECT_START Power sequence NOTE_START Needed for 5V => 20V The Primary Input & Always-On (AON) Tier: - [n:PPDCIN_AON]=5V or 20V. Check CD3217 if missing. - [n:PPBUS_AON] = 12.3V (battery) / 12.0V (MagSafe, no battery). If missing investigate [p:U5200] (ISL9240 charger IC). Fuses [p:F5200] / [p:F5201] at board edge. - [n:PP3V8_AON] = 3.8V Generated by [p:U7700]. If missing or shorted, inject voltage and check [p:U7700] for heat. - [n:PP1V8_AON] = 1.8V LDO from [p:U7700] - [n:PP1V2_AON] = 1.2V LDO from [p:U7700]. Filter cap [p:C7768]. - [n:PP1V5_AON_VCORE_MPMU] = 1.5V LDO from [p:U7700] - [n:PP1V5_AON_VCORE_SPMU] = 1.5V LDO from [p:U7700]. Filter cap [p:C7780]. - [n:PP3V3_AON] = 3.3V Generated by [p:U8100] (MPMU). Check schematic p.41. - [n:PMU_VDDHI] = ~2.5V Ratio-derived from [n:PPBUS_AON]. ~2.45V when PPBUS=12.4V. Once PP3V8_AON is stable, the system enters AWAKE ("Pre-Boot") state - [n:PP1V2_AWAKE] = 1.2V created by [n:SPMU_BUCK8_LX0] - [n:PP1V8_AWAKE] = 1.8V Crucial rail that powers the SPI ROMs [p:U2000] / [p:U2010] and basic I/O logic. Diode mode ~0.342 to GND. - [n:PPVDD_ECPU_SRAM_AWAKE] = 0.8-0.9V Static RAM power for the embedded subsystem General Power (State) Signals - [n:PMU_CLK32K_SOC] = 32.768kHz - [n:PMU_SYS_ALIVE] - [n:PMU_ACTIVE_READY] The S2 Tier (Main System Initialization) All S2 and AWAKE rails must be present for M1 to proceed with boot. - [n:PP5V_S2_MAIN] = 5.0V Powers downstream 5V switches and peripheral logic. Switcher [p:U5700], enable signal [n:P5VS2TPS_PWR_EN] from [p:U8100]. Check [p:RC260] for enable. - [n:PP3V3_S2] = 3.3V Main 3.3V rail for general logic handling. From [p:U8100]. - [n:PP1V8_S2] = 1.8V Used for general peripheral interfaces and memory controllers. Inductor [p:L7830]. - [n:PP1V2_S2] = 1.2V Used for general peripheral interfaces and memory controllers. Inductor [p:L8280]. - [n:PP0V8_S2_CLVR_VDDDIG] = 0.8V - [n:PP1V8_S2SW_CLVR_VDDC1_LDO] = 1.8V The S1/S0 Tier (Power Up & Main Boot Execution) - [n:PPVDD_CPU_S1] = Core CPU S1 supply - [n:PPVDD_SOC_S1] = Core SoC S1 supply - [n:PP1V8_S1] = 1.8V - [n:PP1V2_S1] = 1.2V - [n:ALL_SYS_PWRGD] = ~1.8V (High when all buck regulators are healthy) - [n:SPI_NOR_CS_L] = CS toggle at boot (U0500) Apple Silicon integrates the SSD controller directly into the M1 Pro chip. Because of this security architecture, if any SSD rail is missing or shorted, the CPU panic-loops, causing the entire power sequence to reset continuously (your amp meter might repeatedly cycle from 5V -> 20V -> 0V) - [n:PP0V9_NAND0] 0.9V - [n:PP1V2_NAND0] 1.2V - [n:PP2V5_NAND0] 2.5V - [n:NAND0_BCM_L] 1.2V - [n:NAND0_OCARINA_PGOOD] ~3.7V (must be stable; power cycling = SSD or NAND issue) NOTE_END SECT_END SECT_START Key ICs NOTE_START 820-02098 IC reference - [p:U5200] = ISL9240 Charger / PPBUS_AON buck-boost converter - [p:U7700] = AON PMIC Generates PP3V8_AON and all AON LDOs (1V8, 1V2, 1V5) - [p:U8100] = MPMU (Master PMIC) Generates S2 rails, PP3V3_AON, S2 enable signals. Schematic p.41-43. - [p:U5700] = PP5V_S2_MAIN switcher - [p:U5000] = Secure Element (T2-equivalent function) - [p:UF900] = CD3217 USB-C ACE / PD controller (all 3 ports) NOTE_END SECT_END SECT_START Quick triage NOTE_START Stuck at 5V / not booting checklist 1. [n:PPBUS_AON] present and stable? -> [p:U5200] / fuses [p:F5200],[p:F5201] 2. [n:PP3V8_AON] present? -> [p:U7700]. Diode mode to GND expected ~0.350-0.400. Wait 15s after power off before measuring. 3. [n:PP3V3_AON] + [n:PP1V8_AON] + [n:PP1V2_AON] all present? -> [p:U8100] LDOs (schematic p.41) 4. [n:PP5V_S2_MAIN] present? -> [p:U5700] + check enable signal [n:P5VS2TPS_PWR_EN] at [p:RC260] 5. [n:PP3V3_S2], [n:PP1V8_S2], [n:PP1V2_S2] all stable? 6. [n:PP1V8_AWAKE] present? 7. NAND rails stable? -> If [n:NAND0_OCARINA_PGOOD] unstable, SSD or NAND issue. NOTE: Board will NOT run from USB-C alone without battery connected. Use MagSafe 3 if battery is absent. NOTE_END SECT_END DIAGNOSIS_DATA_END ### END